How old is your wood burner

I have been heating with a Vermont Casting wood stove for 12 years since moving to Pennsylvania. A tri-axel load of logs, about , equals 7 cords.

Love it. I also enjoy the exercise of cutting and splitting my fuel. I did break down and buy a 35 ton wood splitter this fall, what a time saver! I have a Black Bart wood stove built into the fireplace.

Here in coastal SC we do not have severe winters, but nothing takes the chill out as quickly and as comforting as a wood fire in the stove. When the box reaches a certain temp, it blows warm air and heats much of the downstairs, aND rhe cat loves to lie where the warm air first hits the floor!

Keeps heating bills low, is peaceful and comforting, and beautiful! Love wood stoves! Not only do we still stay warm even with no electricity, but I can make a pot of soup on the stop and put bread underneath and make homemade bread to go with it!

My grandparents had a wood stove right in the middle of their kitchen and the in winter it was the focal point of winter living. My grandfather would fire it up in the early morning and put in a log or two when he thought it needed it. It would go all day only dying out late at night. During the big white porcelain clad box would have everyone around it at one point in time.

There were two kitchen stools on both sides and a rocker and recliner a short distance from the front. The best spot was on one of the stools as the heat radiated right at you. Especially coveted after a cold time outdoors in the snow. It held function beyond heating as my grandmother would us it for cooking as well having 6 square feet of cook top and a big oven it's use saw many pie and keeping food warm while the main stove cooked away on the meals.

Best thing was reheating her chocolate donuts to prepare them for confectioners sugar. As I initially said it became a social magnet as many a conversion was heard around the stove. I remember many neighbors and family sitting for hours and learning more about their lives and thoughts. Very much the social point of the house. While I was in the Army in the late 's, I built my own home around a wood burning stove.

I now live in a sf with loft old log cain. I also heat with wood when below 40degress. The best wood to burn is whatever you can get for free. I cut storm damged trees to get most of my wood. I try toseason it at least 6 months, and oak and hickory are the best heat producers. Skip to main content. By The Editors. November 30, What do you want to read next? You may want to have a chimney sweep check the chimney and a mason make any repairs that may be needed.

With a masonry chimney, the stove pipe should be extended through the chimney wall to its inner face, but not beyond. Use high-temperature cement to fasten the pipe to the masonry. If you have no suitable chimney or if you prefer not to close off your fireplace, a factory-built chimney listed by a recognized testing laboratory is a good solution. It should extend at least three feet above the highest point where it passes through the roof of the building and at least two feet higher than any portion of a building within 10 feet.

The stove pipe should be of corrosion-resistant steel of suitable gauge. These are the standards set by NFPA:. NFPA standards also call for a stove pipe to have an internal cross-sectional area not less than that of the stove's flue collar. The pipe should be as straight and short as possible, with sections properly secured.

If it must have angles, limit them to one or, at the most, two sweeping degree elbows or the equivalent. The horizontal portion of the pipe should rise not less than one-quarter inch to the linear foot, to insure a good draft. You should not pass a stove pipe through a combustible wall for a hook-up with a chimney flue. However, if there is no alternative, the stove pipe must be passed through a thimble or collar.

NFPA has set these standards:. It can be made by a local sheet metal company or tinsmith. Material for closing this opening must be noncombustible and insulating. If a wood burning stove has an automatic draft regulator controlled by a thermostat, the manufacturer's instructions for installing it must be carefully followed.

Alternately, a manually operated damper can be installed on the pipe near the stove. This damper should not obstruct more than 80 percent of the pipe area. A second damper higher up on the vertical section of the stove pipe is advisable to permit shutting down the stove in case of a chimney fire.

You can have this made by a local sheet metal company or a tinsmith. Green wood has too high a moisture content for satisfactory use. When you rely on a wood-burning stove for heat, using quality firewood is the key to convenience, efficiency and safety. We went to Fairbanks, Alaska to ask an expert. Featured Posts Latest Post. Get in Touch Check out our social media account. If you enter the room dimensions H x W x D into our output calculator link below , this will show you the recommended stove size for that living space.

As a rule of thumb, you want to allow approx. I would like to buy an inset wood burner from you. Thank you. Nestor Martin are a very well-built stove brand so you have done well to inherit one! With regards to the suitability of this burner for your living space, are you able to see if the data plate is still attached to the rear or side of it?

This would tell you the model name or code and the precise KW output of it. Your email address will not be published. Skip to content You can find out the appropriate wood burner size in kilowatts by: Calculate the cubic space of the room by multiplying the width, height and length. As a rule of thumb, divide the cubic space by 14 and this will give you a KW output needed for the room.